White Glue / PVA

STRONG FIX WHITE GLUE

SYNTHETIC RESIN ADHESIVE

STRONG-FIX WHITE GLUE were the first of its kind to be manufactured in India in 1958. Today STRONG-FIX has become synonymous with strong bond in wood and furniture industry. STRONG-FIX WHITE GLUE is a Synthetic Resin Adhesive in the form of a milky white viscous paste and is ready to use. STRONG-FIX GLUE gives very strong bond. The bond is so strong that if two wooden pieces are joined with STRONG-FIX WHITE GLUE and a hammer is hit heavily. the wood will give way but not the STRONG-FIX bond.

Features:

Unsurpassed bonding strength. Resistant to water and heat. Economical in long run. Gives higher coverage.

Uses:

For bonding wood, plywood, laminates, veneers, particle board, block board/hard board, MDF to each other. Pencil mfg., sports goods, paper labeling, paper tube, wall paper, carpet mfg. Also recommended for bonding any two material where at least one of them is porous eg. paper, card board, particle board etc. Other related applications.

How to Apply:

STRONG-FIX WHITE GLUE can be applied with brush, roller, spreader or fingers. The usual procedure to be followed is: Clean both the surfaces to be bonded. Apply a thin coat of STRONG-FIX WHITE GLUE on both or one surface (as per requirement). Press the two surfaces together and keep under pressure till the adhesive dries completely. Excess adhesive presssed outside the joints should be wiped out with a wet cloth.

rubber adhesive

STRONG-FIX GLUE GOLD

FAST SETTING SYNTHETIC RESIN

For the first time in India, a revolutionary adhesive which can save time and increase productivity.

Features:

Gives handling strength in 2 hours. Saves time – more productivity. Save labour – cost effective. Resistant to water and heat.

Uses:

In time bound projects. For bonding wood, plywood, laminates, veneers, particles board, block board/hard board, MDF to each other.

How to Apply:

Make sure the surfaces to be bonded are properly Cleaned and free from dust, dirt, oil, etc. Apply STRONGFIX GLUE GOLD on both the surfaces to be bonded. In case one surface is more porous than other, the adhesive should be applied first on the less porous surface.

Finish applying the adhesive and pressing of the surfaces to be bonded with in 10 minutes. Keep both the surfaces under pressure with tape, nail etc. The bonded surfaces achieve handling strength in just 1.5 to 2 hours. Time to achieve bonding strength depends on the environmental conditions.

Synthetic Rubber Adhesive suppliers

STRONG-FIX ANCHOR

SYNTHETIC RESIN ADHESIVE

As we all know a piece of furniture undergoes a lot of stress due to change in weather/moisture/infrequent and continuous exposure to water. This may result in opening of joints and debonding of laminates inspite of using good quality material e.g. Marine plywood. STRONG-FIX ANCHOR is specially designed for bonding in furniture, which is exposed to water or placed in high humidity areas.

Features:

48 hour continuous water resistance. 1 hour boiling water resistance. Superior bonding in marine plywood. Higher coverage.

Uses:

For bonding wood, plywood, laminates, veneers, particle board, block board/hard board, MDF to each other.Kitchen units, wall units, bathroom where exposure to water is high. Pencil mfg., sports goods, paper labeling, paper tube, wall paper, carpet mfg. Also recommended for bonding any two material where at least one of them is porous eg. paper, card board, particle board etc. Other related applications.

How to Apply:

STRONG-FIX ANCHOR can be applied with brush, roller, spreader or fingers. The usual procedure to be followed is: Clean both the surfaces to be bonded. Apply a thin coat of STRONG-FIX ANCHOR on both or one surface (as per requirement). Press the two surfaces together and keep under pressure till the adhesive dries completely. Excess adhesive pressed outside the joints should be wiped out with a wet cloth.

synthetic resin adhesive